Solder a wire to this point and the other wire to any ground. next to the "SELECT" SMD tactile switch, there is a solder point "SPR0" this is your right speaker. If you do not have the top screen or the ribbon was cut, then this will be the only was to get sound. Place the speaker in the front side under the A/B buttons. Connect the ribbon cable and bend it backwards and fit it in the shell as you place the motherboard back in the bottom shell as you prepare to reassemble. Solder wires to the speaker contacts and pcb. If your DS had the top screen still attached with the ribbon undamaged, open the top half and remove the ribbon cable along with the small PCB. The way I place the resistor has less of a footprint then the other methods and is more convenient. Others solder an LED instead of the resistor. This involves having the ribbon cable intact and disassembling the top screen to harvest the LED ribbon cable. (NOTE) Most people salvage the led's from the top half of the screen and leave them attached to the little PCB to get the system to turn on. Place in back half of the shell, insert the battery and turn the system on. If not cut it will make the case hard to close, not to mention it will snap the resistor off and it could ruin the system. This small piece on the shell serves to support the motherboard from the back side. The direction the resistor is facing does not matter.īe sure to cut off the small part of the back shell seen here. Place the resistor on the back side resting on the motherboard and bend the leads over.Ĭut off the excess leads and bend down and solder to the points. I have made my own method for placing the resistor on the board. Next to the "START" SMD tactile switch, you will find solder points LED C2 and LED A2, this is where you will need to solder a 1k ohm resistor. Now that the shell is done, time to power up the system. Once ready for paint, prime, paint a color of your choosing and apply a clear coat to protect the paint. Sand the shell fully to get a nice and even surface for painting. it makes it lighter not to mention it causes less problems when closing the shell if you filled in the cart slot on the back side of the shell. (OPTIONAL STEP) - Remove the DS cart holder completely from the motherboard. On the back side, fill in the pen hole and cartridge slot as you will not need it anymore. Once fully apart place everything in a plastic bag to not loose any piecesĬut down the excess top screen hinges and fill in the holes left over with epoxy of your choice.īE SURE TO NOT FORGET to make speaker holes in the front side under the A/B buttons. Take apart the DS completely but keep the DS bottom screen connected. I will keep the guide quick but throrough. They are very different and there is virtually no room inside this shell, the space is really compact. I will be making a separate guide for the DS lite. The nintendo DS need the top screen to turn on, but in this guide you will find how to trick it to think it is. If this is the case then the DS still works. If it flickers and turns off this is due to the top screen not being connected. Please use a DS that turns on and preferably has the top screen still attached. Let me Explain a few things to save you some trouble: Once that is Done we will have something like this.Click to expand.This guide is for making your own Gameboy MacroĮssentially a bottom screen only DS original with the top screen cut off. The Workaround that I applied works as a mix between the previous 2 methods, but to a more direct degree, see here is thing, we can directly connect the LEDs to the spot present in "Method #1", all we have to do is get them out of the top screen by following "Method 2" and desolder them from the ribbon cable, then carefully remove them. This notion can be found in the following Methods.:īy using a 330 OHM Resistor, one can solder said resistor in a specif spot of the motherboard and get the console ready to go, this can be considered the primary method of many tutorials and the one that is the focus of ĭissasembling the Top Screen and carefully cutting just the ribbon cable that is directly connected to it while preserving the LED connection and the start of the ribbon cable will allow you to reconnect the whole thing to its original port, esentially "Stripping" the top screen of the console and making the DS turn on. There are many different methods to get a Gameboy Macro, but the most critical aspect of any of them is making the DS Complete the Boot Sequence by fooling the system into thinking that the LEDs of the Top Screen Are Working, in other words, as long as that check is passed the console will boot.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |